Problem Hub
Last updated:

How to Fix PRINTER Print Spooler Authentication Failed After Firmware Update With Low Memory

Device: printer Code: print spooler authentication failed after firmware update with low memory Read time: ~1 min

Share this guide or save it for later.

Meaning

This guide covers printer issue "print spooler authentication failed after firmware update with low memory" with a staged diagnostic path and safe recovery steps. Printer failures are usually caused by queue state, connectivity (USB/Wi‑Fi), driver mismatch, or firmware state drift. Error codes can vary by model, so treat the steps below as a safe baseline and cross-check the exact code meaning in your printer manual if the issue persists.

Common Causes

  • Temporary state mismatch after partial updates.
  • Conflicting background service or cached artifacts.
  • Network, account sync, or permission constraints.

Quick Fix

Quick path for print spooler authentication failed after firmware update with low memory: - Restart the Print Spooler service (Windows) if jobs are stuck. - Set the printer as Default and ensure it is not paused/offline. - Clear the print queue and retry one test page. - Check connection: USB cable seated or Wi‑Fi connected to the correct network. - Power cycle the printer (off 30 seconds), then power it on and retry.

Common Scenarios

  • Issue appears after an update or configuration change.
  • Failure repeats after restart when background services load.
  • Problem triggers only under specific network or permission conditions.
  • The issue appears right after a system update while applying package changes for print spooler authentication failed after firmware update with low memory.
  • The error is triggered only for administrator actions and service startup flow on printer.
  • The failure repeats after reboot because dependency files are still locked by another process.

Advanced Fix

If it persists: - Remove and re-add the printer, then reinstall the latest driver package. - Update printer firmware if the error repeats after reboot. - Try printing via a different interface (USB vs Wi‑Fi) to isolate connectivity. - Reset network settings on the printer and reconnect to Wi‑Fi. - If the error indicates hardware (fuser/paper path), inspect for jams and run vendor diagnostics.

User Reports

  • [MEDIUM] Resolved after clearing cached artifacts and restarting.
  • [MEDIUM] Stopped happening after disabling a conflicting background app/agent.
  • [LOW] printer user restored normal updates after running DISM and restart sequence.
  • [MEDIUM] Issue reproduced during install pipeline, then fixed after permissions reset for system folders.
  • [HIGH] Error cleared after disabling conflicting third-party service and re-running setup.

FAQ

What is the fastest fix for PRINTER print spooler authentication failed after firmware update with low memory?

Start with quick steps first, then apply advanced recovery only if the issue reproduces after restart.

What is the most common cause?

Most cases are caused by state drift after updates, cached artifacts, or connectivity and permission conflicts.

Should I reinstall?

Only as a last resort. Validate the quick and advanced steps and confirm the root cause before reinstalling.

How do I confirm it is fixed?

Repeat the exact failing workflow twice after applying a fix and monitor whether the symptom returns after restart.

What should I try next if it keeps happening?

Use related links from the same cluster to compare neighboring signatures and isolate the root condition chain.

Can I ignore print spooler authentication failed after firmware update with low memory on printer?

No. Ignoring print spooler authentication failed after firmware update with low memory can block updates or degrade system stability. Apply the quick fix first, then advanced steps if needed.

How long does it take to fix print spooler authentication failed after firmware update with low memory?

Typical recovery takes 10-30 minutes. Deep repair scenarios can require up to one hour including reboot and validation.

Which troubleshooting lane should I use first for print spooler authentication failed after firmware update with low memory?

Start with the update recovery path. Use quick checks first, then move to deeper recovery only if the symptom reproduces.

Intent Pathways

Continue with adjacent guides grouped by intent so diagnosis stays within the same failure lane.

Network Fix Paths

Update And Install Paths

Account And Access Paths

Performance And Stability Paths

Common Fixes

Newly Reported Errors

Recent Trending

Recently Updated

Most Searched (Cluster)

Was This Helpful?

Your feedback helps us prioritize improvements.

Next Troubleshooting Steps

If the issue persists, continue with the most relevant adjacent guides below.

  1. How to Fix PRINTER Print Spooler Slow Printing After Firmware Update On A Home Office Setup
  2. How to Fix PRINTER Print Spooler Slow Printing After Firmware Update On A Workstation
  3. How to Fix PRINTER Print Spooler Slow Printing After Driver Update With Photo Paper Selected
  4. How to Fix PRINTER Print Spooler Slow Printing After Driver Update With Borderless Printing
  5. How to Fix PRINTER Print Spooler Slow Printing After Driver Update With Toner Save Mode
  6. How to Fix PRINTER Print Spooler Slow Printing After Driver Update With High Resolution Mode
  7. How to Fix PRINTER Print Spooler Slow Printing After Driver Update With Low Memory
  8. How to Fix PRINTER Print Spooler Slow Printing After Driver Update With Paper Size Mismatch